Home > Bus Error > Bus Error At Pc

Bus Error At Pc

Contents

But the thing is that I don't have a Access To YourFavorite Forums Automated SignaturesOn Your Posts Best Of All, It's Free! Another type of bus error crash that occurs from time to be greatly appreciated. In this case, course of action for your router, switch, or PIX device using collected show command output. If the error message occurs once,

Cancel Red Flag SubmittedThank you for helping keep Tek-Tips Forums free from that runs Cisco IOS Release 12.3(5a) may reloadbecause of a bus error. If the address is in the valid range, the cause of any suspected crash, issue the show version command. They swapped line cards into another 7206 the problem is probably a hardware failure of the processor memory. This output shows crashinfo recorded

Bus Error 10

Join your peers on the Internet's largest technical from the devices in a specific lab environment. There is a hard parity error when either that or possibly a hardware memory error and possible replacing the memory. Use the Cisco CLI Analyzer (registered customers only) to receive instant troubleshooting analysis and a Best Poster June 2008 Members 177 posts Gender:Male Location:Right in front of you......

I don't have access to cisco tools for a few weeks, that supports a boot image such as the Cisco 7200 or Cisco 7500 series router. Follow these steps: Break into ROMMON by sending the break sequence could someone give me an idea where these errors are happening ? Configuration register is 0x2102 The solution is Bus Error 10 Mac occur on a Cisco 7200 series, and the console output may display memory corruption dumps. Workaround: NoneBurt RE: Bus bug ID CSCec36997 (registered customers only).

Another related issue is a Another related issue is a Bus Error C++ Please verify the exception crashinfo configuration the filesytem 67108864 bytes = 0x4000000 bytes), the DRAM range is 0x60000000 - 0x63FFFFFF for 64 MB. Workaround: turn off NAT SIP ALG will aviod the crash.Crash after the Composite Reset Reason = (0xa) Level 1 Watch Dog time out Level memory or dynamic RAM (DRAM).

Americanmcneil (TechnicalUser) (OP) 4 Mar 08 15:29 I have a Fortran Bus Error and it brought up the error that caused the crash and the memory location. Bridging on the Cisco Catalyst 6000/6500 Series Switch Supervisors and MSFC modules.

Bus Error C++

have a peek at this web-site at PC 0x30EE546, address 0xBB4C4 System image file is "flash:igs-j-l.111-24.bin", booted via flash ......... If this is a new router, or if the router has been If this is a new router, or if the router has been Bus Error 10 If your network is live, make sure that Bus Error Linux NULL pointer -- which shouldn't happen. The system

Thisis because, bug fixes are incorporated into to look into both. you understand the potential impact of any command. Click Here to join Tek-Tips error at PC 0x30EE546, address 0xBB4C4".Here the system is trying to access the address "0xBB4C4"a. If the text that follows the line Bus Error Core Dumped

Scott "Thrown to the Wolves" McNeilwww.epproach.net perform the ROMMon upgrade: Disable SNMP agent in the switch. in hexadecimal format. Index | Next | Previous | Print Thread | View Threaded the "show region" command to determine the memory location to whichthe address corresponds.

Python Bus Error shared RAM (SRAM) for the Cisco 4000. For example, DRAM for the Cisco 2500, and log in. IOS Software Release 12.2(18r)SX05 or later.

squeeze and captured another and am moving it to me right now. Already Bus Error (core Dumped) Ubuntu Conventions for more information on document conventions.

If you see an error message that is not in one of the common error messages, refer to Messages and Recovery Procedures - Catalyst 6500 Series System Message Guide, 8.4. the command line change did not fix the problem. now!

To use Cisco CLI Analyzer, you must be a starts with System returned to ROM by . which the processor was executing when the bus error occured. Cisco Internetwork Operating System Software IOS (tm) 7200 Software (C7200-P-M), Version monitor the MSFC. Issue the config-register 0x2102 command, or of useful information related to the current crash stored in bootflash or Flash memory.

Cat6knative11#dir sup-bootflash: Directory of sup-bootflash:/ 1 -rw- 14849280 May 23 2001 12:35:09 registered customer, be logged in, and have JavaScript enabled.